登陆WRTnode2P（telnet或ssh）
使用microUSB供电，一头接在WRTnode2P标准底板的迷你usb接口，一头接到一个超过500ma的5v供电的地方，上电以后，WRTnode2P底板上的蓝灯亮起，里面的OpenWrt开始启动了，20秒后就能发现一个WRTnode2P_xxxx（xxxx指WRTnode2P mac地址的后四位）的Wi-Fi，用电脑或手机或ipad连上，密码是12345678。
首先通过ping openwrt.lan看看连上WRTnode2P没有，WRTnode2P的IP地址是192.168.8.1，openwrt.lan这个域名会被WRTnode2P拦截并解析到自己的ip地址。
如果第一次登陆WRTnode2P，或者之前没有给OpenWrt的root用户设置密码，那就telnet：
$ telnet 192.168.8.1
或是
$ telnet openwrt.lan
或者已经设置过root密码了，那就ssh:
$ ssh root@192.168.8.1
或是
$ ssh root@openwrt.lan
联网
aps是WRTnode的自定义命令，扫描当前的Wi-Fi，结果如下所示：
# apsWRTnode AP scaner.Begin scaning APs, pls wait...Finished.APs available are...ra0 get_site_survey:Ch SSID BSSID Security Signal(%) 1 TP-LINK_0C9FE8 3c:46:d8:0c:9f:e8 NONE 0 1 MERCURY_42D4 e4:d3:32:de:42:d4 WPA1PSKWPA2PSK/AES 0 2 360 c8:3a:35:05:13:80 WPAPSK/AES 0 2 superficial d8:42:ac:6a:14:40 WPA1PSKWPA2PSK/TKIPAES 29 6 HUAWEI-HT8AYK b0:e5:ed:c7:7f:38 WPA2PSK/AES 0 6 TP-LINK_403 50:bd:5f:00:a6:90 WPA1PSKWPA2PSK/AES 0 6 FAST_C98E9E11 8c:21:0a:c9:8e:9e WPA1PSKWPA2PSK/AES 0 7 Phicomm_2CBFA0 f0:eb:d0:2c:bf:a0 WPA1PSKWPA2PSK/TKIPAES 10 11 TP-LINK_FE42 24:69:68:e4:fe:42 WPA1PSKWPA2PSK/AES 0
然后将WRTnode2P连上路由器：
# setwifi 连接的路由器SSID 对应的密码
看看WRTnode2P有没有从上级路由DHCP获取IP地址:
root@OpenWrt:/# iaapcli0 Link encap:Ethernet HWaddr 66:51:7E:00:82:8C inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6451:7eff:fe00:828c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:134 errors:0 dropped:0 overruns:0 frame:0 TX packets:83 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:31804 (31.0 KiB) TX bytes:6514 (6.3 KiB)
获取到IP后，看看是不是已经连上互联网了：
root@OpenWrt:/# ping www.baidu.comPING www.baidu.com (115.239.211.112): 56 data bytes64 bytes from 115.239.211.112: seq=0 ttl=55 time=5.686 ms64 bytes from 115.239.211.112: seq=1 ttl=55 time=8.942 ms64 bytes from 115.239.211.112: seq=2 ttl=55 time=5.893 ms^C--- www.baidu.com ping statistics ---3 packets transmitted, 3 packets received, 0% packet lossround-trip min/avg/max = 5.686/6.840/8.942 ms